![]() Should my mother install it again? The point is that my mother has some problems with new technology, and I’m abroad and I can’t return to do this. My mum have tried several days,but it still doesn’t work. She has worked with it during 2 days without any problems and then it stopped: Roborock disappeared from the her app. Then I return to my house and I left Roborock at my mom’s house. You real need to solve this issue with a cancel button, to cancel cycle of cleaning. Sometimes returns immediately to docking other lasts 3 or 4 minutes. I need to move it with my own hands and then I put it in the higher part. How can I finish the cleaning cycle, if I can’t cancel it? I do not have a docking downstairs. One of the big issues is to finish cleaning in the part (in my case the lower part) where is no docking. So, there are physical obstacles (wall) and Roborock doesn’t detect these walls.Īfter that Roborock' work varies a lot: some days it is OK and other days it is a headache for me. It still detects zones behind some walls, as from the beginning. Near the stairs the problem was solved, but I can clearly see parts of the two maps overlapped. I put a physical obstacle between the lower part and the higher part. The question is preventing that it can detect these parts overlapped (inside the house), not to forbid the physical moving. It won’t go there, buy these parts overlapped exist to Roborock. Even in this situation, Roborock will identify this parts that were forbidden, and the confusion remain. But the issue is not the physical moving. If I set a no go zone or invisible wall around the area which is outside of the house and the others that are inside the house, but which belong to the lower part, I will forbid Roborock to go to these parts. Roborock will be very confused with this, won’t it? The problems with confusion to identify where it is will remain, won’t they? So, it will have an incomplete cycle and at the same time I will move it to approach it from the docking (I will move it to the higher part). So, it can´t finish this cycle of cleaning and I can’t do this manually, except if I start another one. It means that when I will clean a room at the lower part and it will finish the work, it will try to find the docking to finish this cycle of cleaning. ![]() I will do this just once and I will map with docking at the higher part (for instance). The first one is to use a board or a ramp to map the floor. But sorry! I didn’t get the point of your suggestions. What can’t I do to solve this? Thank you in you. I can’t use Roborock like this, because when I change the part of the house, I’m facing several issues. I’ve tried to solve this partial overlapping of maps erasing these extensions of the higher part’s map, but I can’t erase it. I don’t have any door to close in order to prevent this extension of the higher part’s map. This second extension spans these 3 steps and a small area of the lower part of the house near these 3 steps. The second extension of the higher part’s map is near the 3 steps that divides the two parts of the house. One of this extension of the higher part’s map is behind a wall, so I don’t know how it detect this lower part behind the wall. Second, the map of the higher part of the house extents to the lower part of the house. This happen when I move it from the higher part of the house to the lower (and vice versa).įirst, I try several ways to solve this problem: sometimes I turn off Roborock, before moving it to the other part of the house sometimes don’t. Other time, after looking for the his localization during several minutes and several times, it can finally recognize the map. It doesn’t work anymore, because it doesn’t know where it is in this moment. Sometimes when I restore the map, Roborock doesn’t recognize it, and starts looking for the map during several minutes and then returns to the docking. So, I need to restore the map of this part of the house (manually). But when I put Roborock on the other part of the house, it can’t find alone that part’s map. Roborock works well when it works several times at the same part of the house. I did the first map and the second with the docking. I've a different map for each part, because Roborock can’t go downstairs alone (3 steps). I've a house with two parts (not two floors), which are separated by 3 steps. ![]() For two week I'm in the possessing of a S4 Pure.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |